Send to e-mail

Send to e-mail

A link for this product will be send to the Recipient. If You want to ask us a question about this product, please refer to the Contact section.

Recipient:* 
Your E-mail: 
Your name: 
Message: 


* Your name and E-mail will be show in message with link to product.

The kit of the classic generator functions
The range of 50 - 5KHz
Build according to the attached manual
(see the photo for this product)
Components it is necessary soldered to pcb
(see the photo for this product)

ICL8038 Datasheet:

With excellent performance ASIC chip function generator ICL8038, add a small amount of resistive and capacitive components, can produce sine, triangle and square wave, and the frequency of the signal, duty cycle, adjustable distortion sine wave.

Notice:
Requires a certain DIY ability, you need to weld the kit yourself:)

Description:
ICL8038 pin functions:
1 foot, 12 foot: sine waveform adjusting terminal;
2 foot: sine wave output;
3 foot: triangle wave output;
4 foot, 5 foot: the frequency and duty cycle (or waveform asymmetry) adjustment;
6 foot: In +, the positive power supply;
7 foot: offset; 8 foot: frequency adjustment input terminal;
9 foot: square wave output.
This is an open collector output terminal, the work should take and the load resistor to the corresponding positive power supply terminal from the pin, get a TTL-compatible square-wave output, the load resistance must be connected to + 5V power supply;
10 foot: timing capacitor terminal;
11 foot: V-, negative power supply terminal or the ground. Use the positive and negative power supply, 11 feet to the negative supply, the output waveform are symmetrical with respect to 0V; use a single positive power supply, 11 feet grounded, the output waveform is unipolar, uniform voltage is + VCC / 2;
13 feet, 14 Feet: Empty foot.
The kits are designed for, and frequency range is 50-5KHz, two bands with and switch With this switch, RP1 is the frequency adjustment, RP2 is the duty cycle adjustment, the RP3 is a sine wave distortion adjustment. Circuit uses a 12V single power supply, input from the X1; X2, X3 is a waveform output side, you can use the oscilloscope's observe the three output waveforms.

Model: ICL8038
Input 12V DC
Frequency range 50-5KHz,
Size:6cm*4.5 cm*0.2 cm
Weight:26g

Contact form

Contact form

Name: 
E-mail: 
phone: 
Odesláním formuláře uděluji provozovateli webových stránek dobrovolný souhlas se zpracováním svých osobních údajů, které jsem ve formuláři uvedl. Tyto údaje mohou být použity výhradně pro komunikaci k tématu této zprávy a mohou být uchovány po dobu komunikace.

You might also be interested in

Digital storage Oscilloscope DS0138 200khz

Digital storage Oscilloscope DS0138 200khz
New completely spájená version. Immediately to use. Digital storage oscilloscope Model: DSO138 Processor ARM
Videos Tutorials Heureka
 
In stock 34
52,09 tax incl. 43,05 tax excl.

Power supply module soldering field

Power supply module soldering field
Specifications: the Easiest way to connect to the soldering field voltage. The module can connect most of the
Videos Tutorials Datasheets Heureka
 
In stock 33
2,57 tax incl. 2,12 tax excl.

White Aquarium thermometer LCD -50 ℃ ~ + 110 ℃

White Aquarium thermometer LCD -50 ℃ ~ + 110 ℃
Thermometer For aquarium T110 TPM-10 2m Warning. Part of the supply not the battery. Needed LR44 battery
Datasheets Heureka
 
In stock 253
5,00 tax incl. 4,13 tax excl.

PT100 temperature sensor platinum on the cable

PT100 temperature sensor platinum on the cable
Waterproof thermometer on the cable, type PT100, temperature range -20 to 450 ℃, sensor Ø 4, cable length 0.5
Tutorials Datasheets Heureka
 
In stock 224
2,13 tax incl. 1,76 tax excl.

Pump mini ultra-quiet DC 3-6V 120 L/H

Pump mini ultra-quiet DC 3-6V 120 L/H
DC Voltage: 2.5-6V maximum lift: 40-110 cm, flow rate: 80-120 L / H, the outside diameter of the drain water:
Videos Tutorials Datasheets Heureka
 
In stock 94
3,70 tax incl. 3,05 tax excl.

Watch for availability